1,500m²/h
Maximum approximate productivityR3 commercial mower
A practical platform for repeatable grounds work.
The R3 pairs route-based autonomous mowing with direct remote control. Review the verified current specification below, then tell us about your site.
Request Commercial PricingR3 product imageVerified photography pending
450mm
Cutting width2.5hours
Approximate working time20°max
Suitable slope limitProduct overview
Commercial capability, clearly bounded.
Designed for commercial grounds maintenance, the R3 supports autonomous route planning, defined restricted zones and centimetre-level positioning assisted by a base station. Remote control remains available for operator intervention.
Site suitability depends on terrain, traffic, grass conditions, access, boundary setup and safe operating procedures. The base specification should not be treated as dynamic obstacle avoidance or fully automated charging.
Current supported capabilities
- Autonomous route planning
- Autonomous mowing
- Resume from interruption
- Static obstacle-area marking
- Restricted-zone setup
- Remote control
- Working-status display
Verified product data
R3 technical specification
Values marked “approximately” or “up to” depend on operating conditions.
Machine dimensions795 × 615 × 500 mm
Machine weight62 kg
Battery48V LiFePO₄, replaceable
Working timeApproximately 2.5 hours
Charging timeApproximately 2.5 hours
Mowing productivityUp to approximately 1,500 m²/h
Cutting width450 mm
Cutting height20–70 mm
Blade disc power800W
Drive motors4 × 250W servo motors
Drive and steeringFour-wheel independent drive and steering
TurningZero-turn capability
Maximum speedApproximately 6 km/h
Maximum suitable slope≤20°
Ingress protectionIP54
Remote control2.4G remote control
PositioningBase-station-assisted, centimetre-level positioning
Navigation
Base-station-assisted centimetre-level positioning supports boundary setup, restricted zones, route planning and resuming after interruption.
Battery
The replaceable 48V LiFePO₄ battery provides approximately 2.5 hours of working time and approximately 2.5 hours charging time.
Cutting
A 450 mm cutting width, 20–70 mm height range and 800W blade disc support up to approximately 1,500 m²/h.
Operating boundaries
What the base specification does not claim.
- Dynamic obstacle avoidance is not included in the current base navigation specification.
- Automatic return-to-charge and a fully automatic charging station are not included in the current base specification.
- IP54 does not mean the machine is intended for continuous operation in rain.
- Site suitability must be assessed for complex terrain, slopes and high-traffic areas.
Warranty
12 months for non-wear components.
Actual warranty handling is confirmed according to the specific order and the nature of the product fault.
Read warranty information →Australian orders
Compliance is handled during preparation.
Australian compliance requirements are handled as part of the order preparation process where applicable. We do not claim current RCM certification.
Review the delivery process →Questions before quotation
R3 FAQ
Is the R3 intended for residential lawns?+
The R3 is positioned for commercial and large-area grounds work. Small residential lawns are not the primary use case.
Can it work autonomously?+
Yes. The current configuration supports boundary and restricted-zone setup, route planning, autonomous mowing and resuming after an interruption. A site assessment is still required.
Can an operator take control?+
Yes. A 2.4G remote-control mode is available when manual positioning or intervention is needed.
Does it automatically avoid moving people or vehicles?+
Dynamic obstacle avoidance is not part of the current base navigation claim. The R3 is best assessed for controlled, lower-traffic mowing environments with appropriate site procedures.
Does it return to a charging station automatically?+
Automatic return-to-charge and a fully automatic charging station are not included in the current base configuration.
What is the Australian compliance status?+
We do not claim current RCM certification. Australian compliance requirements are handled as part of order preparation where applicable.
How soon can an order be delivered?+
Timing is confirmed during quotation and depends on destination, order preparation and applicable compliance requirements.
Can I request another configuration?+
Yes. Tell us about your site and operating requirements, and available configuration options can be discussed during the enquiry process.
Commercial enquiry
Request an R3 commercial quotation
Send the core facts about your site so configuration, delivery and compliance requirements can be discussed together.
- Response target
- Within one business day
- Market
- Australia
- Alternative
- Chat on WhatsApp →